Type DID-R

Active chilled diffuser with radial air discharge, 600 or 625 mm nominal width, vertical heat exchanger and condensate drip tray

 

Active chilled beam for heating and cooling, with 2-pipe or 4-pipe heat exchanger, for integration with various ceiling systems. The condensate drip tray is useful if the temperature temporarily falls below the dew point.

  • Preferably for room heights up to 4.20 m
  • High heating and cooling capacity with a low conditioned primary air volume flow rate and low sound power level
  • High comfort levels due to low airflow velocity in the occupied zone
  • Three nozzle variants to optimise induction based on demand
  • Circular or square diffuser face


Optional equipment and accessories

  • Control package
  • Casing powder-coated black
  • Heat exchanger powder-coated black
  • Powder coating in many different colours, e.g. RAL CLASSIC or NCS
small_tab1_Serie DID-R
  • Application
  • Description

Application

  • Active chilled diffusers of Type DID-R for the integration into various ceiling systems, preferably for room heights up to 4.20 m
  • Particularly suitable for continuous ceilings and for grid ceilings with grid size 600 or 625
  • 2-pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate
  • Energy-efficient solution since water is used as a medium for heating and cooling
  • Active chilled diffuser with radial air discharge

Special characteristics

  • Radial air discharge
  • Vertical heat exchanger as 2-pipe or 4-pipe system, with condensate drip tray that is useful if the temperature temporarily falls below the dew point
  • Water connections at the side, Ø10 mm Cu pipe with plain tails

Variants

  • DID-R: Circular construction, Ø598 mm
  • DID-R-Q: With square diffuser face (593, 618, 598, or 623 mm)

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Useful additions

  • Connecting hoses
  • Control equipment consisting of a control panel including a controller with integral room temperature sensor; valves and valve actuators; and compression couplers

Construction features

  • Spigot is suitable for circular ducts to EN 1506 or EN 13180
  • Removable induced air grille, fixed with a central fixing screw, secured with safety cables
  • Plastic nozzles
  • 3 suspension points for on-site installation (by others)
  • Water connections at the side, Ø10 mm Cu pipe with plain tails
  • Three nozzle variants to optimise induction based on demand

Materials and surfaces

  • Casing made of galvanised sheet steel
  • Diffuser face made of aluminium
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Heat exchanger also in black (RAL 9005)
  • Casing powder-coated black (RAL 9005) as an option

Información técnica

  • Function
  • Technical data
  • Quick sizing
  • Specification text
  • Order code
did_r

Functional description

Active chilled beams provide centrally conditioned primary air (fresh air) to the room and use heat exchangers for additional cooling and/or heating.

The primary air is discharged through nozzles into the mixing chamber; as a result of this, secondary air (room air) is induced via the induced air grille and passes through the vertical heat exchanger, where it is heated or cooled.

 

Primary and secondary air mix and are then supplied to the room through the supply air slots horizontally and radially.

did_r
did_r

 

Active chilled diffusers of Type DID-R, with radial air discharge and high thermal output, providing high thermal comfort levels.

For installation flush with the ceiling, preferably in rooms with a height up to 4.20 m.

The units consist of a casing with suspension points, a spigot, and a vertical heat exchanger with condensate drip tray.

Nozzles in three sizes to optimise induction based on demand.

Special characteristics

  • Radial air discharge
  • Vertical heat exchanger as 2-pipe or 4-pipe system, with condensate drip tray that is useful if the temperature temporarily falls below the dew point
  • Water connections at the side, Ø10 mm Cu pipe with plain tails

Materials and surfaces

  • Casing made of galvanised sheet steel
  • Diffuser face made of aluminium
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Heat exchanger also in black (RAL 9005)
  • Casing powder-coated black (RAL 9005) as an option

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Technical data

  • Nominal size: 600, 625 mm
  • Circular diffuser: Ø598 mm
  • Square diffuser: 593, 598, 618, 623 mm
  • Height: 250 mm
  • Primary air spigot, diameter: 98 mm
  • Primary air volume flow rate: 12 – 25 l/s, 43 – 90 m³/h
  • Cooling capacity: up to 550 W
  • Heating capacity: up to 500 W
  • Max. operating pressure: 6 bar
  • Max. operating temperature: 75 °C
did_r

Compartir

Recomendar

Recomendar el contenido de esta página, mandar por mail.

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Compartir

Gracias por su recomendación!

Su recomendación ha sido enviada y llegará a su destino en breve.


Contacto

Estamos aquí para atenderles

Visual contact Visual contact

Por favor mande su solicitud
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Contacto

Gracias por su mensaje.

Visual contact Visual contact

Su mensaje ha sido enviado correctamente, en breve será atendido.
En seguida nos pondremos en contacto con Vd.
Para información general sobre productos o servicios, por favor llamar al:
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Contacto

Estamos aquí para atenderles

Visual contact Visual contact

Por favor mande su solicitud
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Archivo adjunto (Max. 10MB)

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Contacto

Gracias por su mensaje.

Visual contact Visual contact

Su mensaje ha sido enviado correctamente, en breve será atendido.
En seguida nos pondremos en contacto con Vd.
Para información general sobre productos o servicios, por favor llamar al:
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04