Type SMART BEAM

Multi-service active chilled beam with two-way air discharge and horizontal heat exchanger

 

Active chilled beam for heating and cooling, with 2-pipe or 4-pipe heat exchanger, for freely suspended installation; additional functions or services (e.g. lighting, loudspeakers, sprinklers, smoke detectors, or PIR sensors) can be integrated

  • Preferably for room heights up to 4.20 m
  • High heating and cooling capacity with a low conditioned primary air volume flow rate and low sound power level
  • High comfort levels as a result of low airflow velocities in the occupied zone
  • Unit consists of three parts: wall end, active section, and front end


Optional equipment and accessories

  • Control package
  • 3 different front ends
  • Various services, e.g. lighting, sprinklers, smoke detectors, PIR sensors, and loudspeakers
  • Powder coating in many different colours, e.g. RAL CLASSIC or NCS
small_tab1_Serie DID-SB
  • Application
  • Description

Application

  • Active chilled beams of Type DID-SB (SMART BEAM) for freely suspended installation, preferably for room heights up to 4.20 m
  • Project-specific integration of functions or services such as lighting, loudspeakers, sprinklers, smoke detectors, or PIR sensors
  • 2-pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate
  • Energy-efficient solution since water is used as a medium for heating and cooling
  • Integral strip light fittings use innovative microprism optics to provide uniform illumination of rooms
  • Each section can be individually designed

Special characteristics

  • Freely suspended active chilled beam with choice of different face plate perforations
  • Heat exchanger as 2-pipe or 4-pipe system
  • Wide range of additional services such as lighting, sprinklers, loudspeakers and sensors (accessories)
  • Water connection at the narrow side, Ø12 mm Cu pipe, either with plain tails or with G½" external thread and flat seal

Wall end

  • Cover for air and water connections at the side facing the wall
  • Connection of project-specific services


Active section

  • Air discharge and heat exchanger
  • Integration of different functions, e.g. acoustic fleece, lighting or sensors


Front end

  • Available in three designs
  • Integration of project-specific functions, e.g. loudspeakers

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Accessories

  • Sprinkler
  • Smoke detector
  • PIR sensor
  • Loudspeaker
  • Indirect and/or direct lighting

Useful additions

  • Connecting hoses
  • Control equipment consisting of a control panel including a controller with integral room temperature sensor; valves and valve actuators; and compression couplers (no lighting control)

Construction features

  • Spigot is suitable for circular ducts to EN 1506 or EN 13180
  • Unit consists of three parts: wall end, active section, and front end
  • Four suspension points for on-site installation (by others)
  • Four nozzle variants to optimise induction based on demand
  • Perforated front plate (choice of different designs) with acoustic fleece at the rear

Materials and surfaces

  • Wall end as well as active section with front plate, nozzle plate and cross bars are made of galvanised sheet steel
  • Front end made of aluminium or galvanised sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces at the front are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Exposed surfaces at the rear, including nozzle box, in RAL 9006, white aluminium
  • Heat exchanger also available in RAL 9006, white aluminium

Información técnica

  • Function
  • Technical data
  • Quick sizing
  • Specification text
  • Order code
smartbeam

Functional description

Active chilled beams provide centrally conditioned primary air (fresh air) to the room and use heat exchangers for additional cooling and/or heating.

The primary air is discharged through nozzles (four variants are available).

As a result of this, secondary air (room air) is induced and passes through the heat exchanger.

Primary and secondary air mix and are then supplied to the room horizontally.

smartbeam
smartbeam

 

Active chilled beams of Type DID-SB, with two-way air discharge and high thermal output, providing high thermal comfort levels; for visible installation about 300 mm below the ceiling slab in rooms without a suspended ceiling.

Preferably for room heights up to 4.20 m.

The units consist of a casing with suspension points, a spigot, non-combustible nozzles, and a horizontal heat exchanger.

Nozzles in four sizes to optimise induction based on demand.

Special characteristics

  • Freely suspended active chilled beam with choice of different face plate perforations
  • Heat exchanger as 2-pipe or 4-pipe system
  • Wide range of additional services such as lighting, sprinklers, loudspeakers and sensors (accessories)
  • Water connection at the narrow side, Ø12 mm Cu pipe, either with plain tails or with G½" external thread and flat seal

Wall end

  • Cover for air and water connections at the side facing the wall
  • Connection of project-specific services


Active section

  • Air discharge and heat exchanger
  • Integration of different functions, e.g. acoustic fleece, lighting or sensors


Front end

  • Available in three designs
  • Integration of project-specific functions, e.g. loudspeakers

Materials and surfaces

  • Wall end as well as active section with front plate, nozzle plate and cross bars are made of galvanised sheet steel
  • Front end made of aluminium or galvanised sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces at the front are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Exposed surfaces at the rear, including nozzle box, in RAL 9006, white aluminium
  • Heat exchanger also available in RAL 9006, white aluminium

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Technical data

  • Length: 4500 – 5200 mm
  • Height: 291 mm (plus services)
  • Width: 750 mm
  • Primary air spigot, diameter: 123 mm
  • Primary air volume flow rate: 8 – 33 l/s, 30 – 120 m³/h
  • Cooling capacity: up to 1000 W
  • Heating capacity: up to 750 W
  • Max. operating pressure: 6 bar
  • Max. operating temperature: 75 °C
smartbeam

Compartir

Recomendar

Recomendar el contenido de esta página, mandar por mail.

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Compartir

Gracias por su recomendación!

Su recomendación ha sido enviada y llegará a su destino en breve.


Contacto

Estamos aquí para atenderles

Visual contact Visual contact

Por favor mande su solicitud
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Contacto

Gracias por su mensaje.

Visual contact Visual contact

Su mensaje ha sido enviado correctamente, en breve será atendido.
En seguida nos pondremos en contacto con Vd.
Para información general sobre productos o servicios, por favor llamar al:
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Contacto

Estamos aquí para atenderles

Visual contact Visual contact

Por favor mande su solicitud
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04

Archivo adjunto (Max. 10MB)

Los campos marcados con un (*) sin imprescindibles de cumplimentar

Contacto

Gracias por su mensaje.

Visual contact Visual contact

Su mensaje ha sido enviado correctamente, en breve será atendido.
En seguida nos pondremos en contacto con Vd.
Para información general sobre productos o servicios, por favor llamar al:
Tel.: +34 976 50 02 50 | Fax: +34 976 50 09 04